these specifications apply to the agilent technologies e7402a and E7405A emc analyzers. frequency specifications frequency range e7402a dc coupled 100 hz 1 to 3.0 ghz ac coupled 100 khz 1 to 3.0 ghz E7405A band lo harmonic = n 0 1- dc coupled 30 hz 1 to 3.6 ghz ac coupled 100 mhz to 3.6 ghz 1 1- 2.85 ghz to 6.7 ghz 2 2- 6.2 ghz to 13.2 ghz 3 4- 12.8 ghz to 19.2 ghz 4 4- 18.7 ghz to 26.5 ghz frequency reference aging 1 x 10 C7 /year temperature stability 1 x 10 C8 settability 1 x 10 C8 frequency readout accuracy (start, stop, center, marker) (frequency indication x frequency reference error 2 + span accuracy + 15% of rbw + 10 hz) + 1 hz x n 3 specifications all specifications apply over 0 c to +55 c unless other- wise noted and are covered by the product warranty. the analyzer will meet its specifications when: its within the one year calibration cycle, auto align [all] is selected, stored a minimum 2 hours within the operating tempera- ture range, turned on for at least 5 minutes, and align now rf has been run once every 24 hour period. typical per- formance describes the level at which 80% of the units will meet or exceed with a 95% confidence level over 20 to 30 c, but is not covered in the product warranty. characteristics describe expected product performance levels that are not covered in the product warranty. agilent e7400a series emc analyzers data sheet 1. usable to 30 hz 2. frequency reference error = (aging rate x period of time since adjustment + settability + temperature stability) 3. n = lo harmonic mixing mode
2 marker frequency counter 1 accuracy 2 (marker frequency x frequency reference error 3 + counter resolution) counter resolution selectable from 1 hz to 100 khz frequency span range 0 hz (zero span), 100 hz x n 4 to the range of the spectrum analyzer resolution 2 hz x n 4 accuracy (> 2000 sweep points) sweep type linear 0.5% of span sweep type log 2% of span (characteristic) sweep time range span > 0 hz 1 ms to 4000 s span = 0 hz 50 ns 5 to 4000 s accuracy 1% sweep trigger free run, single, line, video, external, delay, offset, and gate (option 1d6) delay trigger range 1 s to 400 s sweep (trace) point range 101 to 8192 span = 0 hz 2 to 8192 resolution bandwidth 1 hz to 3 mhz (C3 db) in 1-3-10 sequence 6 5 mhz (C3 db) bandwidth 200 hz 6 , 9 khz, 120 khz, 1 mhz (C6 db) emi bandwidths 1 mhz (impulse) emi bandwidth accuracy 1 hz to 300 mhz (C3 db) 10% 1 khz to 3 mhz (C3 db) 15% 5 mhz (C3 db) 30% 200 hz (C6 db) 10% 9 khz to 120 khz (C6 db) 20% 1 mhz (C6 db) 10% 1 mhz (impulse) 15% selectivity (characteristic) 10 hz to 300 hz (C3 db) < 5:1 (C60 db/C3 db) (digital, approximately gaussian-shaped) 1 khz to 3 mhz (C3 db) < 5:1 (C60 db/C3 db) (approximately gaussian-shaped) 200 hz (C6 db) < 3:1 (C40 db/C6 db) (digital, kaizer windows) 9 khz, 120 khz, 1 mhz (C6 db) < 10:1 (C60 db/C6 db) (approximately gaussian-shaped) 1 mhz (impulse) < 10:1 (C60 db/C6 db) (approximately gaussian-shaped) video bandwidth range 30 hz to 3 mhz 7 in 1-3-10 sequence 1, 3, 10 hz for rbws < 1 khz stability noise sidebands (1 khz rbw, 30 hz vbw and sample detector) stability specifications specified typical 1 khz na C78 dbc/hz 8 10 khz C90 dbc/hz 8 C94 dbc/hz 8 > 20 khz C100 dbc/hz 8 C105 dbc/hz 8 > 30 khz C106 dbc/hz 8 C112 dbc/hz 8 > 100 khz C118 dbc/hz 8 C122 dbc/hz 8 > 1 mhz C125 dbc/hz 8 C127 dbc/hz 8 > 5 mhz C127 dbc/hz 8 C129 dbc/hz 8 > 10 mhz C131 dbc/hz 8 C136 dbc/hz 8 residual fm 1 khz rbw, 1 khz vbw 100 x n 4 hz pk-pk in 100 ms 10 hz rbw, 10 hz vbw 2 x n 4 hz pk-pk in 20 ms system-related sidebands 30 khz offset from cw signal C65 dbc + 20 log n 4 typical performance spec -70 -90 -110 -130 1k 10k 100k 1m offset (hz) dbc/hz 1. not available in rbw < 1 khz 2. marker level to danl > 25 db, span 1.5 ghz, rbw/span 0.002 3. frequency reference error = (aging rate x period of time since adjustment + settability + temperature stability) 4. n = lo harmonic mixing mode 5. rbw 1 khz, 2 sweep points 6. 1 hz to 300 hz are only available in spans of 5 mhz. this bandwidth is not usable when the tracking generator is turned on (option 1dn). 7. characteristic 8. add 20 log(n) for frequencies > 6.7 ghz.
3 amplitude specifications amplitude range measurement range displayed average noise level (danl) to ma ximum safe input level input attenuator range e7402a 0 to 65 db (75 db 1 ), in 5 db steps E7405A 0 to 65 db, in 5 db steps maximum safe input level average continuous power +30 dbm (1 w) peak pulse power +50 dbm (100 w) (input attenuator 30 db) maximum dc 0 vdc (dc coupled) 50 v (ac coupled) 1 db gain compression (total power at input mixer 2 ) 50 mhz 0 db 6.7 ghz C3 db 13.2 ghz C5 db display range log scale 0.1, 0.2, 0.5 db/division and 1 to 20 db/ division in 1 db steps; ten divisions displayed rbw 1khz 0 to C85 db from reference level is calibrated rbw 300 hz 0 to C120 5 db from reference level is calibrated linear scale 10 divisions scale units dbm, dbmv, dbv , dba, amps, volts and watts marker readout resolution log scale 0 to C85 db 0.04 db 0 to C120 (rbw 300 hz) 0.04 db linear scale 0.01% of reference level fast sweep times for zero span (option ayx) log scale, 0 to C85 db 0.3 db linear 0.3 % of reference level 1. characteristic 2. mixer power level (dbm) = input power (dbm) C input attenuator (db) 3. typical 4. 0 to 50 db for rbws 300 hz and span = 0 hz, or when auto ranging is off, or 0 to 30 db for rbw = 200 hz. 5. 0 to C70 db range when span = 0 hz, when rbw = 200 hz, or when if gain is fixed. display average noise level (danl) 1 khz 10 hz 1 khz 10 hz 1 hz rbw rbw w/preamp w/preamp w/preamp on on, typical on, typical e7402a 30 hz to 9 khz 3 na C93 na na na 9 khz to 100khz 3 na C109 na na na 100 khz to 1 mhz 3 na C135 na na na 1 mhz to 10 mhz 3 C117 C136 na C152 C162 10 mhz to 1 ghz C117 C136 C152 4 C156 C166 1 ghz to 2 ghz C116 C135 C153 4 C156 C166 2 ghz to 3 ghz C114 C133 C151 4 C154 C164 E7405A 30 hz to 9 khz 3 na C93 na na na 9 khz to 100khz 3 na C109 na na na 100 khz to 1 mhz 3 na C135 na na na 1 mhz to 10 mhz 3 C117 C137 na C155 C165 10 mhz to 1 ghz C116 C135 C151 4 C157 C167 1 ghz to 2 ghz C116 C131 C151 4 C155 C165 2 ghz to 3 ghz C112 C131 C149 4 C152 C162 3 ghz to 6 ghz C112 C131 na na na 6 ghz to 12 ghz C111 C130 na na na 12 ghz to 22 ghz C107 C126 na na na 22 ghz to 26.5 ghz C106 C125 na na na
4 frequency response (10 db input attenuation) absolute 1 typical relative flatness 2 30 hz to 3 ghz 3 0.5 db na 0.5 db 3.0 ghz to 6.7 ghz 1.5 db 0.39 db 1.3 db 6.7 ghz to 13.2 ghz 2.0 db 0.68 db 1.8 db 13.2 ghz to 26.5 ghz 2.0 db 0.86 db 1.8 db input attenuation switching uncertainty at 50 mhz attenuation setting 0 db to 5 db 0.3 db 10 db reference 15 db 0.3 db 20 to 65 db (0.1 db + 0.01 x attenuator setting) absolute amplitude accuracy typical at reference settings 4 0.34 db 0.13 db preamp on 5 0.37 db 0.14 db overall amplitude (0.54 db + absolute accuracy 6 frequency response) rf input vswr 3 (at tuned frequency, 10 db attenuation) e7402a 100 hz to 100 khz 1.1:1 100 khz to 3 ghz 1.4:1 E7405A 100 hz to 100 khz 1.1:1 100 khz to 6.7 ghz 1.3:1 6.7 ghz to 13.2 ghz 1.5:1 13.2 ghz to 22 ghz 2:1 22 ghz to 26.5 ghz 2.2:1 resolution bandwidth switching uncertainty (referenced to 1 khz rbw, at reference level) 10 hz to 3 mhz rbw 0.3 db 5 mhz rbw 0.6 db 10 hz to 300 hz rbw 0.3 db reference level range C149 dbm to max. mixer level + attenuator setting resolution log scale 0.1 db linear scale 0.12% of reference level accuracy (reference level 0.3 db (C10 dbm to C60 dbm) C attenuator setting 0.5 db (C60 dbm to C85 dbm) + preamp gain) 0.7 db (C85 dbm to C90 dbm) display scale fidelity log maximum cumulative rbw 1 khz db below reference level typical 0 db (reference) 0.00 db 0.00 db > 0 db to 10 db 0.3 db 0.08 db > 10 db to 20 db 0.4 db 0.09 db > 20 db to 30 db 0.5 db 0.10 db > 30 db to 40 db 0.6 db 0.23 db > 40 db to 50 db 0.7 db 0.35 db > 50 db to 60 db 0.7 db 0.35 db > 60 db to 70 db 0.8 db 0.39 db > 70 db to 80 db 0.8 db 0.46 db > 80 db to 85 db 1.15 db 0.79 db rbw 300 hz (span > 0 hz) 0 db to 98 db (0.3 db + 0.01 x db from reference level) 98 db to 120 db (2.0 db from reference level) 3 log incremental accuracy 0 db to 80 db 7 0.4 db/4 db from reference level linear accuracy 2% of reference level linear to log switching 0.15 db at reference level 1. referenced to 50 mhz amplitude reference (20 c to 30 c) 2. reference to midpoint between highest and lowest frequency response deviations. (20 c to 30 c) 3. characteristic 4. reference level C20 dbm; input attenuation 10 db; center frequency 50 mhz; rbw 1 khz; vbw 1 khz; scale linear or log; span 2 khz; sweep time coupled, sample director, signal at reference level. 5. 1 hz to 300 hz are only available in spans of 5 mhz and are not usable with tracking generator option 1dn. 6. for reference levels 0 to 50 dbm; input attenuation 10 db; dc coupled; rfw 1 khz; vbw 1 khz; scale loge range 0 to C50 db from reference level; sweeptime coupled; signal input 0 to 50 db; spsn 20 khz. 7. 0 to 50 db for rbws 300 hz and span = 0 hz, or when auto ranging is off, or 0 to 30 db for rbw = 200 hz.
5 spurious responses second harmonic distortion 10 mhz to 500 mhz < C65 dbc for C30 dbm tone at input mixer 1 500 mhz to 1.5 ghz < C75 dbc for C30 dbm tone at input mixer 2 1.5 ghz to 2.0 ghz < C85 dbc for C10 dbm tone at input mixer 2 > 2.0 ghz < C100 dbc for C10 dbm tone at input mixer 1 (or below dis- played average noise level) third order intermodulation distortion 100 mhz to 6.7 ghz < C85 dbc for two C30 dbm tones at input mixer 1 and > 50 khz separation > 6.7 ghz < C75 dbc for two C30 dbm tones at input mixer 1 and > 50 khz separation other input related spurious < C65 dbc, for C20 dbm tone at input mixer 1 residual responses (input terminated and 0 db attenuation) 150 khz to 6.7 ghz < C90 dbm amplitude ref. output amplitude C20 dbm (nominal) fm demodulation 3 input level C60 dbm + attenuator setting signal level 0 to C30 db below reference level quasi-peak detector specifications the emc analyzer displays the quasi-peak amplitude of a pulse radio frequency on continuous wave signals. amplitude response conforms with publication 16 of comite international special des perturbations radioelectrique (cispr) section 1, clause 2, as indicated in the relative quasi-peak response table. relative quasi-peak response to a cispr pulse (db) pulse repetition 120 khz emi bw 9 khz emi bw 200 hz emi bw frequency (hz) .03 to 1 ghz 0.150 to 30 mhz 9 khz to 150 khz 1000 +8.0 1.0 +4.5 1.0 CCC 100 0 db reference 4 0 db reference 4 +4.0 1.0 60 CCC CCC +3.0 1.0 25 CCC CCC 0 db reference 4 20 C9.0 1.0 C6.5 1.0 CCC 10 C14 1.5 C10.0 1.5 C4.0 1.0 5 CCC CCC C7.5 1.5 2 C26 2.0 C20.5 2.0 C13.0 2.0 1 CCC C22.5 2.0 C17.0 2.0 isolated pulse CCC C23.5 2.0 C19.0 2.0 general specifications temperature range operating 0 c to +55 c storage C40 c to +75 c emi compatibility conducted and radiated emis- sions is in co mpliance with cispr pub. 11/1990 group 1 class b 5 audible noise < 40 dba pressure and < 4.6 bels power (isodp7779) military specification type tested to the environmental specifications of mil-prf- 28800f, class 3 power requirements on (line1) 90 to 132 v rms, 47 to 440 hz 195 to 250 v rms, 47 to 66 hz power consumption < 300 w standby (line 0) power consumption < 5 w dc operation voltage 12 to 20 vdc power consumption < 200 w measurement speed e7402a E7405A local measurement rate 6 45/sec 40/sec remote measurement as gpib transfer rate 7 45/sec 40/sec rf center frequency tuning time 8 75/ms 75/ms data storage (nominal) internal 200 traces 9 or states external (floppy) 200 traces 9 or states 1. mixer power level (dbm) = input power (dbm) C input attenuator (db) 2. not available in rbw < 1 khz 3. characteristic 4. reference pulse amplitude accuracy relative a 66 v cw signal < 1.5 db as specified in cispr pub 16 cispr reference pulse: 0.44 vs for 30 mhz to 1 ghz, 0.316 vs for 150 khz to 30 mhz, 13.5 vs for 9 khz to 150 khz 5. meets class a performance during dc operation or serial number us41110000 or lower. 6. characteristic; factory preset, fixed center frequency, sweep points = 101 auto align off, rbw = 1 mhz, stop frequency 3 ghz, span > 10 mhz and 600 mhz. 7. characteristic; factory preset, fixed center frequency, sweep points = 101 auto align off, rbw = 1 mhz, stop frequency 3 ghz, span = 20 mhz, gpib interface, display and markers off, fixed center fre- quency, single sweep 8. characteristic; includes center frequency tuning and measurement plus gpib transfer times, stop frequency 3 ghz, sweep points = 101, display and markers off, single sweep 9. when storing a 401-point trace plus the instrument state
6 weight (without options) e7402a 14.9 kg (32.9 lbs.) E7405A 17.1 kg (37.7 lbs.) dimensions without handle 222 mm(h) x 409 mm(d) x 373 mm(w) with handle (max.) 222 mm(h) x 516 mm(d) x 416 mm(w) inputs/outputs front panel connectors input 50 type n (f) rf out 50 type n (f) probe power +15 vdc, C12.6 vdc at 150 ma max. characteristic ext. keyboard 6-pin mini-din, pc keyboards (for entering screen titles and file names) speaker front-panel knob controls volume headphone 3.5 mm ( 1 / 8 inch) miniature audio jack power output 0.2 w into 4 1 amptd ref. output 50 , bnc (f) rear panel connectors 10 mhz ref out 50 , bnc (f), > 0 dbm 1 10 mhz ref in 50 , bnc (f), C15 to +10 dbm 1 gate trig/ext. trig in bnc (f), 5 v ttl gate hi swp out bnc (f), 5 v ttl vga output vga compatible monitor, 15-pin d-sub, (31.5 khz horizontal, 60 hz vertical sync rates, non-interlaced) analog rgb 640 x 480 if and sweep ports aux if output bnc (f), 21.4 mhz, nominal C10 to C70 dbm 1 (uncorrected) aux video out bnc (f), 0 to 1 v 1 (uncorrected) hi swp in bnc (f), low stops sweep (5 v ttl) hi swp out bnc (f), (5 v ttl) swp out bnc (f), 0 to +10 v 1 ramp gpib interface standard (option a4h) ieee-488 bus connector serial interface (option 1ax) rs-232, 9-pin d-sub (m) parallel interface standard 25-pin d-sub (f), printer port only 1. characteristic
7 option specifications option 1dn tracking generator frequency range 9 khz to 3.0 ghz output power level range range C2 to C66 dbm resolution 0.1 db absolute accuracy 0.75 db (at 50 mhz) output vernier range 8 db output attenuator range 0 to 56 db, 8 db steps output flatness 9 khz to 10 mhz 3.0 db 10 mhz to 3.0 ghz 2.0 db effective source match (characteristic) 0 db attenuation < 2.0:1 (0 db attenuation) 8 db attenuation < 1.5:1 ( 8 db attenuation) spurious output harmonic spurs (C1 dbm output) 9 khz to 3 ghz < C25 dbc non-harmonic spurs 9 khz to 2 ghz < C27 dbc 2 ghz to 3 ghz < C23 dbc dynamic range maximum output power C displayed average noise level power sweep range (C10 dbm to C1 dbm) C (source attenuator setting) preamplifier (standard) 1 mhz to 3 ghz (nominal gain 20 db)
option ordering information esa/emc spectrum analyzer configuration guide literature number 5968-3412e remove all doubt our repair and calibration services will get your equipment back to you, performing like new, when prom- ised. you will get full value out of your agilent equipment through- out its lifetime. your equipment will be serviced by agilent-trained technicians using the latest factory calibration procedures, automated repair diagnostics and genuine parts. you will always have the utmost con? dence in your measurements. for information regarding self main- tenance of this product, please contact your agilent of? ce. agilent offers a wide range of ad- ditional expert test and measure- ment services for your equipment, including initial start-up assistance, onsite education and training, as well as design, system integration, and project management. for more information on repair and calibration services, go to: www.agilent.com/? nd/removealldoubt agilent email updates www.agilent.com/? nd/emailupdates get the latest information on the products and applications you select. agilent direc t www.agilent.com/? nd/agilentdirect quickly choose and use your test equipment solutions with con? dence. agilent open www.agilent.com/? nd/open agilent open simpli? es the process of connecting and programming test systems to help engineers design, validate and manufacture electronic products. agilent offers open connectivity for a broad range of system-ready instruments, open industry s oftware, pc-standard i/o and global support, which are combined to more easily integrate test system development. www.agilent.com www.agilent.com/? nd/emc for more information on agilent technologies products, applications or services, please contact your local agilent of? ce. the complete list is available at: www.agilent.com/? nd/contactus americas canada (877) 894-4414 latin america 305 269 7500 united states (800) 829-4444 asia paci? c australia 1 800 629 485 china 800 810 0189 hong kong 800 938 693 india 1 800 112 929 japan 0120 (421) 345 korea 080 769 0800 malaysia 1 800 888 848 singapore 1 800 375 8100 taiwan 0800 047 866 thailand 1 800 226 008 europe & middle east austria 01 36027 71571 belgium 32 (0) 2 404 93 40 denmark 45 70 13 15 15 finland 358 (0) 10 855 2100 france 0825 010 700* *0.125 /minute germany 07031 464 6333** **0.14 /minute ireland 1890 924 204 israel 972-3-9288-504/544 italy 39 02 92 60 8484 netherlands 31 (0) 20 547 2111 spain 34 (91) 631 3300 sweden 0200-88 22 55 switzerland 0800 80 53 53 united kingdom 44 (0) 118 9276201 other european countries: www.agilent.com/? nd/contactus revised: august 14, 2008 product speci? cations and descriptions in this document subject to change without notice. ? agilent technologies, inc. 2001, 2003 C 2005, 2008 printed in usa, september 3, 2008 5968-3662e
|
